Notice to all visitors and members of the Train-Sim.Com message forums: If you plan on using a signature banner in your posts, we would like to remind you that there is a maximum size for banners. That maximum is 450 pixels wide by 120 pixels high, and not to exceed 25k. Your compliance is appreciated. FORUM RULES Problems? There are two common reasons for problems with logging in and posting messages. The first is that you are running a firewall that prevents your messages from being sent to the server. The other is that you have cookies disabled; the DCForum software requires cookies to work properly.
hi..further to my recent problem with bve 2.5..i tried to install as said but had the string table error..should i be overwritng my previous version of bve with the 2.5 version or is it a stand alone version..im really not sure what im doing..the instructions on railsim seem to be for 2.4 and looks nothing like what i have downloaded...maybe some could explain in laymens terms exactly what i need to do to get it to work. many thanks...
Hi Lynx, Simply paste everything below into notepad and name it, "string.ini" and put it in your main BVE folder (where BVE.EXE is)JohnFile starts now..... Version=2050001 FontSize0=7 FontSize1=8 FontSize2=11 FontName0="Arial" FontName1="Arial" FontName2="Arial" FontName3="Arial"MsgBox0=" Continue?" MsgBox1="File not found." MsgBox2="Path not found." MsgBox3="Syntax error" MsgBox4="Are you sure you want to quit " MsgBox5="?" MsgBox7=" has started already." MsgBox8="Could not change display resolution." MsgBox9="Could not initialize Direct3D." MsgBox10="Could not change to HAL." MsgBox11="Could not initialize DirectSound." MsgBox12="You must restart " MsgBox13=" before the new settings will take effect." MsgBox14="Please select a train." MsgBox15="Route too long" MsgBox16="Could not load texture" MsgBox17="Invalid vertex index" MsgBox18="Invalid vertex index" MsgBox19="The file format is not supported" MsgBox20="Invalid file format" MsgBox25="Please adjust the number of steps on lever of the TS master controller." MsgBox26="One Lever Cab: " MsgBox27="Two Lever Cab - Power: " MsgBox28=" Brake: " MsgBox30="The train is not found." MsgBox31="The number of errors exceeded the limit." Menu0="&Select Train..." Menu1="&Restart" Menu2="Ad&vice Settings" Menu3="&Beginner" Menu4="&Intermediate" Menu5="&Advanced" Menu6="&Graphics Settings..." Menu7="&Control Settings..." Menu8="&Display Mode Settings..." Menu9="&About" Menu10="E&xit"LampS0="ATS ON" LampS1="ATS ALARM" LampP0="CONTROL POWER" LampP1="PTN APPROACH" LampP2="PTN APP ACCEPT" LampP3="BRAKE APPLY" LampP4="ATS-P ON" LampP5="FAILURE" LampC0="ATC RELEASE" LampC1="ATC" LampC2="EMG OPERATION" LampC3="ATC POWER" LampC4="ATC BRAKE" LampC5="ATC EMERG" Lamp0="EMERG BRAKE" Lamp1="SPEED HOLD"RevHandle-1="R" RevHandle0="N" RevHandle1="F"HandleAab0="SV" HandleAab1="LAP" HandleAab2="REL"Handle1="EMG" Handle2="B" Handle3="HB" Handle4="OFF" Handle5="N" Handle6="P"System0=" TIME " System1=" DOOR " System2="FRAME-RATE " System3="" System4="" System5="PRECEEDING-TRAIN "Advice0="Signal at CAUTION (G+Y=75Km/h Y=55Km/h DY=25Km/h)" Advice1="You are EXCEEDING THE SPEED LIMIT" Advice2="You have overshot the stop point " Advice3="The train has Slid (You need to leave the Brakes on)" Advice4="SIGNAL PASSED AT DANGER (SPAD !!!)." Advice5="You should not stop the continuation chime until train has stopped." Advice6="Turn on ATS power (SHIFT+F2 then INSERT)." Advice7="Change to correct safety device (ATS=Pg Up, ATC=Pg Dn)." Advice8="ATS not cancelled (Press SPACE BAR or CTRL+F2)." Advice9="Emergency Brake not cancelled." Advice10="EMERGENCY BRAKE APPLIED." Advice11="You have caught up with the preceding train." Advice12="Train SETTING BACK." Advice13="Cancel ATS (Apply BRAKE then Press SPACE BAR)." Advice14=" STOP continuation bell.(press INSERT)." Advice15=" Reset Emergency Brake.(Press DELETE)." Advice16=" Reset safety device. (press CTRL+F2 and SHIFT+F2)." Advice17=" Stop position incorrect." Advice18="Overrun: " Advice19=" metres" Advice20=", Delay: " Advice21=" seconds" Advice22="Creating structure... " Advice23="Rendering structure... "Timetable0="Station" Timetable1="Arr." Timetable2="Dep." Caption="Select Train" Label0="File" Label1="Route Overview" Label2="Train Overview" Button0="&Start" Button1="Cancel" Caption="Display Mode Settings" Option0="&Full Screen (640 x 480 pixels)" Option1="&Windowed" Check="&Show this dialog when program starts" Button="OK" Caption="Graphics Settings" Label="Viewing Distance (metres)" Check="&Disable fog effect" Button0="OK" Button1="Cancel" Caption="Control Settings" Option0="&Keyboard" Option1="&Joystick" Option2="&TS Master Controller" Option3="Assign &1" Option4="Assign &2" Button0="OK" Button1="Cancel" Caption0="About " Caption1="" Button="OK" caption="File Read Error" label="Error occurred while reading the file." button0="&Ignore" button1="&Abort"